INFORMATION ABOUT 58 MG OMNITROPE HGH VIALS

Before beginning the Omnitrope Injection Process, clean your hands thoroughly with soap and hot water. Also, ensure that the injection staging area you choose is clean and sterilized as well.

Take the two vials and take off their protective seals. Take your first alcohol swab and disinfect both vials: the vial with the diluent and the vial with the Lyophilized Omnitrope.

Take the three milliliter needle and syringe and put it together. Draw the air out of the syringe, and insert the syringe into the vial of diluent. Inject the air into the vial, flip the vial, and draw the entirety of the bacteriostatic diluent into the syringe, then draw out the needle.

Next, take that syringe and pierce the container which contains the powdered Omnitrope. Very carefully release all of the diluent into the second vial. It's important to allow the fluid to roll down the wall of the glass, as this prevents the reconstituted product from foaming. Draw out the needle and throw it away responsibly.

Take the vial and agitate it slightly. It's important not to shake the solution, however. With enough agitation, the product should appear completely clear. Do not use the product until and unless the Reconstituted Omnitrope is clear.

How to Store Omnitrope HGH

After the Omnitrope Human Growth Hormone has been reconstituted, you have three weeks to use the product. Once reconstituted, store under refrigeration between 36' and 46' Fahrenheit. Before every injection, it is necessary to re-mix the HGH Medication to ensure that it is properly reconstituted.

Upon removal, the Reconstituted Omnitrope should be free of particles and clear. If the medication does not pass this visual test, no longer administer treatment from the vial and throw it away.

Where are the Best Locations to Inject Omnitrope?

An important aspect of Omnitrope Injection to think about before you take the steps to administer the medication is that you must rotate the injection site with every administration. Don't inject the same location twice in a single week. Make sure you inject a minimum of .5 inches from the previous shot.

Best Spots for Subcutaneous Injection of Omnitrope:

• Abdomen

• Buttocks

• Thighs

• Other areas with sufficient fat between muscle and skin

Areas to Avoid Omnitrope Injection:

• Waistline

• In Proximity of the Navel

• Any area of Bruised, Infected, or Damaged Skin

How To Inject Omnitrope HGH

The following are instructions regarding how to self-administer an Omnitrope Human Growth Hormone Shot. These instructions are informational and for reference, and you should only inject Omnitrope Human Growth Hormone Injections after you have been appropriately shown how by a medical professional. If you have any queries regarding the Injection of Omnitrope HGH, contact your physician.

How to Measure an Appropriate Dose of Omnitrope 5.8 mg for Injection

Clean the area of your skin where you intend to inject the Omnitrope with the second alcohol swab. Before injection, allow the alcohol to dry naturally.

Take your 1 milliliter needle and syringe and pierce the reconstituted vial of Omnitrope.

Flip both the syringe and the vial, facing needle upwards. After the vial is turned, make sure that the tip of the needle is fully submerged in the Omnitrope.

Draw the appropriate dose slowly into the syringe, so that it contains exactly the dose of Omnitrope that you intend to inject.

With the needle still pointed upward, draw the syringe from the stopper.

Inspect the syringe to ensure no air bubbles are trapped. If air bubbles are spotted, draw the plunger out a bit, then softly agitate the syringe with your fingertips to free the bubbles from the wall of the syringe. After all air bubbles are collected at the tip of the needle, press down on the plunger until the bubbles are fully eliminated.

How to Deliver an Omnitrope Injection

Take your fingertips and squeeze a patch of skin where you intend to deliver the medication. Take the syringe into your second hand and grip it just like you were using a pencil. If the area is sufficiently thick enough, insert the needle at a ninety degree angle. If the patch isn't quite thick enough, inject at a forty-five degree angle.

After you have inserted the needle, move your first hand from your skin to the barrel of the syringe. Take the plunger with your second hand and draw back very slowly. If you draw blood, do not inject into the skin, because you have accidentally hit a blood vessel. Remove the needle, toss the dose, and start over with clean supplies.

Deliver the Omnitrope HGH Injection by depressing the plunger slowly and completely.

Draw the needle from the site as soon as the dose as delivered. If you are bleeding slightly after the injection, depress sterilized gauze or a bandage over the site for a few moments, or until the bleeding has stopped. Rubbing or massaging the area can lead to irritation and should be avoided.

How to Discard Omnitrope HGH

After the injection process is complete, and you've treated the injection wound if necessary, treat the leftover needles and syringes as sharp, bio-hazardous waste. Toss the used tools into a Sharps container, and do not use HGH until you have an appropriate disposal device available to you. After the Sharps container is full, all you have to do is deliver the box to a pharmacist or appropriate medical professional.